Radiography Testing (RT) of Welds: Film, Digital Imaging and the Safety Question in Indonesia

Radiography testing, or RT, produces an image of the inside of a weld, much like a medical X-ray. For decades it has been the method that buyers trust when they want to see volumetric flaws such as porosity and slag and keep a record they can review years later. It is also the NDT method that brings the greatest safety obligations onto a project.

This article explains how radiographic testing of welds works, what it finds and misses, how film and digital imaging differ, and what radiation safety and regulation mean for projects in Indonesia. For buyers, the safety and scheduling points are often the least understood and the most costly to ignore.

How RT Works

A radiation source is placed on one side of the weld and a detector on the other. Radiation passes through the metal, and areas that are thinner or less dense, such as voids and cracks, let more radiation through. The detector records the differences as darker or lighter areas, and a trained interpreter reads the image to identify flaws.

The geometry of the exposure matters. The beam is normally aimed at the middle of the section being examined and should strike the surface perpendicularly, unless a special technique calls for another angle. In pipes, the source can be placed at the centre for a panoramic shot or outside for a contact shot, and each arrangement has its own coverage and limitations.

Because the method records an image, it produces evidence that can be reviewed by someone else. That reviewable record is one of its main advantages over methods in which the result exists only as a technician’s reading at the time of the test.

X-Ray or Gamma Source?

Two kinds of sources are used. X-ray generators produce radiation electrically, so they can be switched off when not in use, but they need power and are less practical for thick or dense parts. Gamma sources use radioactive isotopes, need no electricity and are portable, but they emit continuously and cannot be turned off.

Common isotopes include iridium-192 and cobalt-60, with the latter producing higher-energy radiation suited to thicker sections. Selenium-75 and ytterbium-169 are also used in industrial radiography. For very thick or dense objects, linear accelerators can be used instead.

The choice affects safety, logistics and image quality. A gamma source brings storage, transport and security obligations because it is radioactive material at all times. An X-ray set brings a power supply and different handling requirements. The contract and the provider’s permits should be consistent with whichever source is planned.

What RT Finds Well, and What It Misses

Radiography is strong at showing volumetric flaws such as porosity, slag inclusions and gross lack of penetration, and it shows their type, size and position on a single image. That is why it has been the traditional choice for pressure-retaining welds and pipelines that call for a permanent record.

It is weaker for planar flaws. Cracks and lack of fusion can be hard to detect if their plane is not aligned with the beam, and even trained viewers can miss them. This is why many projects combine methods, with radiography for volumetric flaws and ultrasonic testing for planar ones, instead of relying on one alone.

Geometry limits are real too. Variation in thickness along the exposed length affects image quality, and complex shapes can be difficult to expose. Access to both sides of the joint is needed, and the detector must be placed correctly. A good radiographer plans the shots before the first exposure.

Film Versus Digital Imaging

Traditional radiography uses film in a lightproof cassette, often with intensifying screens, developed in a darkroom or processor to reveal the image. The film itself is a physical record that can be stored and examined later. Digital systems use imaging plates or flat-panel and similar detectors, and the image appears on a screen without chemical processing.

The industry is shifting from film to digital, much as photography did. Digital offers faster results, no chemicals and easier storage and sharing. Its record is an electronic file rather than a physical object, so the project must specify format, storage, backup and retention to ensure the images remain readable and trustworthy for years.

Standards are being updated to reflect this, and a digital-detector technique now has its own part within the weld radiography standard series. Whichever route is chosen, the contract should state which technique and which standard edition apply, and who owns and keeps the images at the end of the job.

Image Quality and Interpretation

An image is only as useful as its quality. Image quality indicators, such as wire-type or step-hole types placed on the weld, show whether the radiograph has enough sensitivity to reveal flaws of the size the code cares about. A radiograph without a visible indicator at the required level is not a valid test, however clean it looks.

Interpretation requires trained, qualified personnel. The person who takes the exposure and the person who interprets it may be different, and the qualification levels should match the contract. Viewing conditions also matter, with suitable light and a quiet environment for film, and calibrated monitors for digital images.

Buyers should ask who interprets the images and who reviews them. A second review by an independent person on critical welds provides an extra check, and it is one of the better uses of third-party involvement in RT. The report should list the technique, source, geometry, indicator results and the findings against the acceptance criteria.

Radiation Safety on a Working Site

Industrial radiography has a challenging safety history. Public references note that incidents have been linked to fatigue, carelessness, inadequate training and lost sources, which is why regulators and clients treat it seriously. Safety practice rests on three principles: limit the time spent near the source, increase the distance, and use shielding.

Before an exposure, the area must be cleared of other people and the boundary maintained for the whole exposure. Survey meters measure radiation levels, alarming dosimeters warn of high levels and personal dosimeters record cumulative dose. These are not optional extras but the equipment that allows the radiographer to prove the area was safe.

This has a direct effect on schedules. Exclusion zones can stop other trades working nearby, and radiography is therefore often arranged outside normal shifts or in controlled windows. A project that plans radiography late will find it competing with every other activity on the site, so coordination at the planning stage saves both safety risk and money.

Licensing and Regulation in Indonesia

In Indonesia, the use of ionizing radiation sources in industry falls under nuclear regulatory rules overseen by the national agency, BAPETEN, the Badan Pengawas Tenaga Nuklir. These rules cover licensing of the use of radiation sources and the associated safety requirements, and they have been updated in recent years.

For buyers, the practical step is to ask any radiography provider for evidence of its authorization to use and transport the sources it proposes, details of its radiation protection arrangements and the certification of its radiographers. Requirements change, so confirm the current position with the provider and the regulator rather than relying on an old checklist.

Foreign owners should also ask about source management: where the source is stored, how it is transported to the site, and what the emergency procedure is. A provider that handles these questions clearly is likely to handle the rest of the work with the same care. G.I Quality Services lists radiography testing among its NDT services, and the same questions apply to any provider.

Frequently Asked Questions

What is radiography testing used for?

RT is used to examine the internal condition of welds and components by producing an image. It is particularly good at revealing volumetric flaws such as porosity and slag, and it gives a record that can be reviewed later.

What is the difference between X-ray and gamma radiography?

X-ray radiography uses an electrical generator that can be switched off, while gamma radiography uses a radioactive isotope that emits continuously. Gamma sources are portable and need no power but bring storage and transport obligations.

Is digital radiography replacing film?

The industry is moving in that direction because digital offers speed, no chemicals and easier storage. The contract should specify the technique, the standard edition and the arrangements for storing and retaining the images.

Is radiography good at detecting cracks?

It can detect them when they are suitably aligned with the beam, but planar flaws can be hard to see. Many projects therefore combine RT with ultrasonic testing for better coverage of different flaw types.

Why does radiography disrupt other work on site?

Exposures need exclusion zones that must be cleared of people. This often means scheduling radiography outside normal working hours or in controlled periods, which should be planned in advance.

What should I ask a radiography provider about licensing?

Ask for evidence of authorization for the sources, the transport and storage arrangements, radiation protection procedures and the radiographers’ certification. Confirm current regulatory requirements with the regulator.

0 0 reviews
Rate this